Annunciators

After so long time looking for a easy way to implement annunciators, I believe I finally found something very interesting. I am talking of squares plastic boxes. The fit into the holes of the cards for soldering; in the middle go the LEDs and on top you can fit a strip with the written of the annunciator. Finally on top of that goes a protectiv plastic cap so that it is not possible to damage the written with the finger tips.
I fount them at conrad after a long search.
The first model has a transparent cap that for me is the best solution. You can find the with the ID number 705332. An image says much more:

The second model, 702237, has a diffusor on top i.e. it is not transparent:

They have a surface of around 1x1cm, maybe a little more (1 inch?). But I think they are good enough even if not perfect. Perfect for me would be 1x1,5.

Another interesting piece of hardware that I bough just for testing are momentary buttons with the surface coloured by 2 LEDs. The exists in greem (704423), in red (704415) and orange (704431) and yellow. About the same size of the annunciators:

I finally mounted the landing gear on the wooden frame. It is the biggest panel I have in mind so it will take a long time. I thin to place there the flaps (a rotary with annuciators and the gauge I bought from opencockpits), auto brakes, ILS and so one.
I also planned a littler panel having only a rotary for the APU with its 2 annunciators and the push button to communicate with cabin attendandts and ground services. Ok this last part is not very interesting to fly but it is used more often then other controls in the header panel. The other are just set on departure and turned OFF at the apron. I will use this panel to practice with the rotary before using severalof them in the other big panel.

I did not yet bought the gauges from flightillusion: I wrote a email but they never replied...

One word to must be said about my CPFlight MCP. After I upgraded the driver there are several problems. But I am in contact with the support for fixing. I have to say that CPFlight support is always very good. On the other hand I suspect to be the only using their products with the 767: it is something I have to keep in mind for the future.

Planning for new panels

First snow arrived last Saturday and that definitely means that this summer is gone and cold winter is arriving. And when this happen I start planning the new improvements for the home cockpit.

I am planning three panels right now but I have not yet decided their layout. One panel will go on top of the second monitor: there will be all the annunciators from the header panel and from the glare shield. They will be realized with OpenCockpi because it is very easy and fast. I have also noticed that the new version of LekSeeCon has improved a lot during the summer. In particular the part regarding the proximity warnings of the glare shield. The library now connects to FSUIPC too and there are new status bits that, according to Niko, make the behavior of annunciators more similar to the real 767. Current version is 9.2 and there are a lot of improvements and changes comparing to the 8.2 I have installed at home. So I have to upgrade as soon as possible.


Last winter I prepared the wooden frame to put the landing gear and other instruments but at the end I bought and installed the FMC from OpenCockpits and I am really satisfied of this device.
In the frame, I will install the landing gear and something else as I have free room there. The problem is that this panel goes just in front of the joy so it is not very easy to reach. Should I put there some gauge instead?

The third panel will go in the far left side aside of the main monitor. I want to put there some of the controls. For example flaps and brakes but maybe also the switches to communicate with the flight attendants and that to ask for the pushback. The layout is not decided yet, of course.

At this point I have to plan carefully what to put and where because my available space is finishing: I have to concentrate on the most important (i.e. most) used switches, leds and gauges. And for the same reason I have to plan all the panels at the same time even if I have to admit that the panel with the annuciators is almost stand alone and I can start working on that.

I have no room for installing more monitors but I could greatly improve the realism by installing gauges. I have found those produced by flightillusion quite interesting even if very expansive. There is a card to be connected to the PC with a US, the GA-55. It is possible to connect gauges to this card like for example the altimeter (GSA16) and the attitude indicator (GSA34),  and the Radio Magnetic Indicator (GSA-RMI-DME). Quite expansive I know but they seems really good and easy to interface with the simulator. To make the system good enough I would need also a vertical speed indicator.
Considering that I already bought the OpenCockpit gauges for the flaps and the digits and knobs for the ILS tuning, with this gauges and the panels I wish to build I could probably fly without keyboard and without the glareshield in the main monitor.

I started a survey with the hardware producers and I found a very interesting post in MyCockpit.org with a  List Of Third-Party Rudder Pedals, Yokes, TQs, etc... I put the link here as I think is a great reference for everybody.